Begin by cutting off a 10-in. length of the board and setting it aside. Rip the remaining 38-in. board to 6 in. wide and cut five evenly spaced saw kerfs 5/8 in. deep along one face. Crosscut the slotted board into four 9-in. pieces and glue them into a block, being careful not to slop glue into the saw kerfs (you can clean them out with a knife before the glue dries). Saw a 15-degree angle on one end and screw the plywood piece under the angled end of the block.


Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
The saw's blade is precision set and has extra sharpened teeth and it has a good amount of flexibility to give you that much-needed cutting control for all sorts of cross grain cuts. For indoor and outdoor use, the GreatNeck has a weather-resistant dark stained hardwood handle and it is very comfortable to hold. The GreatNeck hand saw is covered by a lifetime warranty.

A luminaria (often called luminary) is a traditional Mexican lantern made from a paper bag with sand and a candle inside. We’ve add some woodworking panache to these outdoor accents and build our luminarias from wood, with box joints and a star-shaped cutout. They’re beautiful — and reusable — ways to brighten patios, steps and walkways this holiday season.


This creative picture frame project will blow your mind and you will start loving it. It’s obviously a cool wooden upcycling idea for DIY decorating at no cost. I just love the vintage look of these picture frames and think you will, too. Especially, when you will get to know how easy is it to build these picture frames at no cost. These wooden frames can make you a handsome profit when you went to sell them.
Cross-cut saw teeth are more difficult to sharpen than rip saw teeth, but very possible (I enjoy doing it). Look for cross cut hand saws with 7-9 ppi (points per inch). If you can’t see the tooth shape up close the PPI number (points per inch) can sometimes assist in identifying a hand saw as a rip hand saw or cross-cut hand saw because rip saws usually have smaller teeth. But the shape of the tooth is the best identifier if you can inspect it in person.
If you have more complex woodworking or carpentry jobs, choose a hand saw that is tailor made for these tasks like the Vaughan BS240P Pull Stroke Rip Handsaw or the Crown FLINN1 10-Inch Dovetail Saw. Also, the type of hand saw will depend on whether you be cutting with the grain or across the grain. There are 3 main types of basic hand saws: a cross cutting saw, a rip saw, and a dovetail back saw.
For an artisanal look, you can use woodworking hand tools. These are easy to use, lightweight and require no batteries or power cords to operate. Many hand tools are covered by multi-year or even lifetime warranties for extra protection and value. Set up your pieces with the most expertly crafted woodworking hardware, such as hinges, pulls and knobs to create a final product that you can give as a gift, sell or just display proudly.
If you have more complex woodworking or carpentry jobs, choose a hand saw that is tailor made for these tasks like the Vaughan BS240P Pull Stroke Rip Handsaw or the Crown FLINN1 10-Inch Dovetail Saw. Also, the type of hand saw will depend on whether you be cutting with the grain or across the grain. There are 3 main types of basic hand saws: a cross cutting saw, a rip saw, and a dovetail back saw.
For an artisanal look, you can use woodworking hand tools. These are easy to use, lightweight and require no batteries or power cords to operate. Many hand tools are covered by multi-year or even lifetime warranties for extra protection and value. Set up your pieces with the most expertly crafted woodworking hardware, such as hinges, pulls and knobs to create a final product that you can give as a gift, sell or just display proudly.
×