We cut the supports 16 in. long, but you can place the second shelf at whatever height you like. Screw the end supports to the walls at each end. Use drywall anchors if you can’t hit a stud. Then mark the position of the middle supports onto the top and bottom shelves with a square and drill 5/32-in. clearance holes through the shelves. Drive 1-5/8-in. screws through the shelf into the supports. You can apply this same concept to garage storage. See how to build double-decker garage storage shelves here.

Build this Queen sized storage bed and pair it with your favorite headboard for a functional and attractive storage piece. This trendy storage bed looks adorable in the room, you can also modify it this bed with your choice. You don’t need to be a professional woodworker, only a few basics of woodworking can be enough to DIY this project. We are including source tutorial link as well as a video tutorial, so that you can take some help.
If you can only afford one initial hand saw, then get a rip saw. A rip saw can indeed make cross cuts (cutting the board to length) though it will require more cleaning up than if you use a cross cut hand saw (read more below). But it is much more difficult to rip a long board with a cross-cut saw. Rip saws are simple to sharpen and refurbish. I have a good number of rip hand saws from different saw makers, but mostly Disston saws. If you find multiple old hand saws for a good price, you can certainly sharpen and set them in different ways to make certain jobs easier. Some of the desirable models of Disston saws are the Disston #16 hand saw, Disston #D-8 hand saw (with thumb holes is desireable), Disston #12 hand saw, among others.
Hand saws are mostly used for rough cutting a board to an approximate size. Rip hand saws, in particular, rip along the length of the grain (“ripping”). Look for a rip hand saw between 4-7 ppi (“points per inch”, or “teeth per inch”).  The ppi will usually be marked on the blade (can you see the number 5 on the above saw blade?). A 4 ppi rip hand saw will remove more wood, but may be more difficult to cut.

Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.


This super easy recycled pallet Christmas tree created by using some pallets is one of my favorite DIY projects. It might have all the components of your craft, a little bit new but rustic Christmas tree. It is perfect for both outdoor and indoor décor pieces! We are including the source tutorial for this DIY project below. Source tutorial includes step by step details of this process with diagrams and images.
There’s no denying the value of a handmade gift. There’s still time to make a project and have it ready to give as a gift this holiday season. Here are fifteen woodworking projects that would make great holiday gifts for a wide range of people. Most are not difficult and some can be completed in a day. You can probably build a few of them with scraps you have around your shop. Just click on the project name to go to the full project article.
Shorter hand saws (around 20-inches long) are officially called “panel saws” because they can fit in the panel of a large tool chest, and they are more suited for fine furniture making. Most normal hand saws run from 24-inches to 30-inches long. Many people mistakenly call all saws of this type “panel saws”. But don’t be rude and correct them! Try out different sizes to see what length you’re comfortable with.
WoodAndShop.com recommends products, with links to online stores, some of which are part of affiliate programs. If users make purchases in those stores (e.g. ebay.com and Amazon.com) those affiliate links lead to referral compensation to us. These payments are very helpful to us, and add no additional fees to our users, so we are grateful for anyone who uses the affiliate links. We run our website based on principles of integrity, and don’t recommend any product that we wouldn’t use ourselves. Any product claim about a service or product should be verified with the manufacturer.
Not every one of us is a fan of wine, but you can’t deny that every house might have a bottle or two that were maybe a gift for any special occasion. So, if you are planning on keeping such wine bottles and popping them for another special occasion, then you have to keep them properly. Keep your favorite wines within reach for some dinner parties and holiday gatherings with one of these well-constructed wine racks.
Commonly used woodworking tools included axes, adzes, chisels, pull saws, and bow drills. Mortise and tenon joints are attested from the earliest Predynastic period. These joints were strengthened using pegs, dowels and leather or cord lashings. Animal glue came to be used only in the New Kingdom period.[3] Ancient Egyptians invented the art of veneering and used varnishes for finishing, though the composition of these varnishes is unknown. Although different native acacias were used, as was the wood from the local sycamore and tamarisk trees, deforestation in the Nile valley resulted in the need for the importation of wood, notably cedar, but also Aleppo pine, boxwood and oak, starting from the Second Dynasty.[4]
The hand saw has a greater TPI, 17 teeth-per-inch, which provides a clean and precise cut and the 1½- inch blade is made from hardened steel with extra brass backing which gives the blade that extra strength to cut through all types of wood, soft and hardwood, and gives it additional resistance to any wear or tear or corrosion, so you can be confident of high-quality results.
It has a narrow and tapered blade, usually pointed at the end. A compass saw typically has about 8-10 teeth per inch, which can go up to 20 teeth per inch if you are cutting harder materials. A compass saw comes with a pistol grip, which is best suited if you are working in confined places. The pointed end helps you penetrate soft materials without requiring a pilot hole.

This can be an elegant centerpiece of your patio furniture or room furniture. Building this project does not need any professional skills, but anyone with basic woodworking knowledge and skills can build this project easily. This project will take three or four hours of your time to build, or can be a day if you take some breaks during the work as I did.


The beauty of this project lies in the simplicity. All you need are 3 pieces of wood of your choice (though we must admit natural hardwoods will look incredible), sanding block, clamps, wood glue and finishing product. The hardest step of the whole tutorial is measuring – as always, measure 9 times, cut once! You wouldn’t want to finish your project and then realize it doesn’t have enough space to fit your DVD player, would you?

Carpenters are trained to work with wood. That means that any part of your home that is built of wood is very likely to involve a carpenter. Framing carpenters will put up the wood that makes up the bones of your home. If you’re having a wood floor installed, it may be done by a carpenter — although being a carpenter is not a requirement to install flooring. Trim, baseboards, wainscoting and any other detail work is typically installed by a finish carpenter. The wood boxes of custom cabinets will be built and installed by a carpenter.
With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
Copyright 2018 by Cut The Wood. CutTheWood.com is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Additionally, CutTheWood.com participates in various other affiliate programs, and we sometimes get a commission through purchases made through our links. 

Working with reclaimed wood is a savvy use of resources, and the material's country appeal is undeniable. With just a saw and a small drill, you can reuse old fencing to make these simple woodworking projects: picket-inspired picture frames. Finish them off by hot-gluing clothespins or bulldog clips to hang your prints. Here’s a step-by-step guide.
“Back saws” are specifically designed for fine joinery work (they have a rigid steel or brass back to keep the blade stiff). Dovetail back saws are the smallest back saws (typically 8-10″) and are configured with fine rip-filed teeth (15-20 ppi) for cutting along the grain (think dovetails). Thinner blades (0.02″ ish) are preferred and I like the pistol grip handle because of my big hands (see above).
The moment we first saw this group’s master lather begin his work, we knew we’d found someone special.  He’s a quiet, steady-handed worker. He smiles and lets his group’s work speak for itself.  And it does. We watched in awe as he chipped away angled pieces of wood from a solid block of thick Mugavu – all done “Michelangelo-style” right in front of our eyes.

Following is everything you need to know about a career as a woodworker with lots of details. As a first step, take a look at some of the following jobs, which are real jobs with real employers. You will be able to see the very real job career requirements for employers who are actively hiring. The link will open in a new tab so that you can come back to this page to continue reading about the career:

The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.
Sound overwhelming? Then just start off focusing on Disston saws. The Disston saws were manufactured by the millions and are the easiest to find, and most are of exceptional quality, especially the below common models. Remember to buy pre 1940’s era vintage hand saws. Here are some ebay searches for wood saws. To ensure that you don’t over-pay, when you’re on ebay click “sold” to see what they’re selling before and to see which saws are desirable. It’s fun research:
I really like building difficult cabinets, laying them out, and assembling them. It really gives me a challenge to build something better each time, but the sanding and clean up are not my favorite aspects of this work; you better get used to it. And I wish I would have taken some business classes because the part of running a business is another element added to cabinet making.
Drill four 5/8-in.-dia. 1/2-in.-deep holes on the large disc?inside the traced circle?then use 5/8-in. dowel centers to transfer the hole locations to the underside of the small disc. Drill four 1/2-in.-deep holes on the underside of the small disc and a 1/2-in.-deep hole in the center of the top for the dowel handle. Glue in the dowels to join the discs, and glue in the handle. We drilled a wood ball for a handle knob, but a screw-on ceramic knob also provides a comfortable, attractive grip.
Typically furniture such as tables and chairs is made using solid stock from hardwoods due to its strength and resistance to warping.[10] Additionally, they also have a greater variety of grain patterns and color and take a finish better which allows the woodworker to exercise a great deal of artistic liberty. Hardwoods can be cut more cleanly and leave less residue on sawblades and other woodworking tools.[10] Cabinet/fixture makers employ the use of plywood and other man made panel products. Some furniture, such as the Windsor chair involve green woodworking, shaping with wood while it contains its natural moisture prior to drying.

Although the term “woodworker” may evoke the image of a craftsman who uses hand tools to build ornate furniture, the modern woodworking trade is highly technical and relies on advanced equipment and highly skilled operators. Workers use automated machinery, such as computerized numerical control (CNC) machines, to do much of the work with great accuracy.

The beauty of this project lies in the simplicity. All you need are 3 pieces of wood of your choice (though we must admit natural hardwoods will look incredible), sanding block, clamps, wood glue and finishing product. The hardest step of the whole tutorial is measuring – as always, measure 9 times, cut once! You wouldn’t want to finish your project and then realize it doesn’t have enough space to fit your DVD player, would you?
Woodworking power tools include various saws for cutting the wood to size and drills for creating holes. Sand pieces down to the finish you want before you sand with portable sanders. Use drivers to install woodworking fasteners for a durable final piece. Cleverly designed rotary tools feature removable bits that can drill, drive, sand, cut and more, so you can use a single tool to accomplish virtually every task of your project. For a production-level project, nail guns can save you hours or even days depending on the work involved.
For our customers who are passionate about woodworking, we offer an extensive selection of tools and accessories to help your woodworking projects come to life. Whether you are a professional carpenter, construction manager or simply wish to build a DIY project, you will find everything that you need on our Amazon.com Woodworking page. Our selection ranges from, screwdriver sets to air filtration, band saws, sanders, drill presses, dust collectors, jointers, laminate trimmers, lathes, planers, benchtop, plate joiners, belt sanders, router combo kits, shapers, sharpener, barn door hardware, circular saws, router tables, router bits, planer, tool box, wood glue, nail gun, table saws, hammers and more.
All content on this blog is the property of Just the Woods, LLC. You are welcome to share my content (to include one photo only) as long as you provide a link back the original post. DO NOT copy entire posts, or crop, edit, or remove watermarks from photos without written permission from me first. Sharing a post from Just the Woods in a capacity where YOU will be compensated is not permitted. Thank you!
×