With a pencil and a protractor, divide the larger disc into 30-degree wedges to create 12 center lines for the bottle indents. Center and trace the smaller disc on top of the larger disc. Next, with a drill press, drill 3/8-in.-deep holes on the 12 center lines with the 1-7/8-in. Forstner bit, spacing them between the disc’s outer edge and the traced circle. Next, divide the smaller disc into 60-degree wedges and drill six more 3/8-in.-deep holes with the Forstner bit.
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.
This box is the fifth generation of this design. After each production run of about 20 boxes, I make slight design changes to enhance the look and simplify the machining. Any hardwoods would work, but since the box uses so little lumber, I prefer to incorporate highly figured woods. For safety, ease of construction and consistent cuts, I use a jig for bevel-cutting the legs and another jig for beveling the top surface of the lid.
There are two types of electric circular saws, the worm drive and the sidewinder. The worm drive saw has enough torque to cut through wet lumber and concrete. The behind-the-blade handle placement reduces kickback, and the blade’s left-side position makes it easy to see your cut line if you’re right-handed. The sidewinder’s motor, attached directly to the blade, weighs less but also has less torque.

If you’re looking to show off you’re woodworking skills and you have a piece of wood with a beautiful linear grain pattern, then this box project is a great choice. It’s a more refined box design, and as you might expect, it’s a little more challenging to build than the simple keepsake box presented earlier on this gift list. The sides are constructed so that the wood grain flows smoothly across one face, around the corner and into the adjoining face — and all the way around the box without a break — the grain itself becomes a major part of the design. The design is also enhanced by tapering the box sides, allowing the eye to more easily take in the continuous run of grain at the corners.
All content on this blog is the property of Just the Woods, LLC. You are welcome to share my content (to include one photo only) as long as you provide a link back the original post. DO NOT copy entire posts, or crop, edit, or remove watermarks from photos without written permission from me first. Sharing a post from Just the Woods in a capacity where YOU will be compensated is not permitted. Thank you!
Build this handy stool in one hour and park it in your closet. You can also use it as a step to reach the high shelf. All you need is a 4 x 4-ft. sheet of 3/4-in. plywood, wood glue and a handful of 8d finish nails. Cut the plywood pieces according to the illustration. Spread wood glue on the joints, then nail them together with 8d finish nails. First nail through the sides into the back. Then nail through the top into the sides and back. Finally, mark the location of the two shelves and nail through the sides into the shelves. Don’t have floor space to spare? Build these super simple wall-mounted shoe organizers instead!
The best thing about this wine rack is that it is very easy to build. All you need is the basic understanding of woodworking and a few tools to get started. You can modify your wine rack any way you want or build in a design or color different from this one. The basic steps to build a wooden wine rack are the same for all variants. I have included here the video tutorial that I followed in order to build myself a pallet wide rack.
A good Japanese pull saw isn't cheap, perhaps $60-75, and they have to be replaced when dull. They also tend to be brittle and teeth can break off if you nick them on your vice. Also, after trying to improve my technique for 9 years, I still can't follow a straight line, the saw goes where it wants to. My newest Japanese saw came with instructions that said to grip the handle with two hands, which I had never thought about nor read anywhere. Could you comment on that, Matt? Thanks.
It might not be the easiest project in this list, but if you already have some experience with wood cutting and joinery, it won’t be any hassle at all. Thanks to the extremely detailed instructions it shouldn’t really be a problem even if you’re not very familiar with woodworking. This could actually be a great project for refining your woodworking skills as a beginner!
And finally, we ended up with an original, elegant, functional and an inexpensive bar that we were able to make ourselves. Even though this shelf project was created as a simple way of adding some useful decorative pieces. Check out our this DIY beautiful piece which is made of reclaimed pallets. It doesn’t involve any scrap, but it is still the project that will look elegant in your room.

There are many factors to consider when deciding what type of wood to use for a project. One of the most important is the workability of the wood: the way in which it responds when worked by hand or tools, the quality of the grain, and how it responds to adhesives and finishes.[9] When the workability of wood is high, it offers a lower resistance when cutting and has a diminished blunting effect on tools.[9] Highly workable wood is easier to manipulate into desired forms. If the wood grain is straight and even, it will be much easier to create strong and durable glued joints. Additionally, it will help protect the wood from splitting when nailed or screwed.[9] Coarse grains require a lengthy process of filing and rubbing down the grain to produce a smooth result.[9]


It is one of the easiest woodwork projects we are going to discuss today. Although it looks very easy to make, I still could not find any good tutorial on the internet that explains how to build this one. So I am here sharing an article link that gets the closest. The article explains how to make different kinds of DIY candle holders and what items you may need for the project.
This rack can be built from old unused wood pallets you can find around the house. So it is also a great way to recycle those old pallets. You can also find a step by step tutorial at instructables.com for which I have included the source link below. This tutorial helps you to make a wood wine rack from the scratch. So what are waiting for? Just grab the items you need and start building a cool wooden rack for those nice wine bottles of yours.
Though I’d not planned to strike out on my own, in 2012, it occurred to me I had gained the experience and skills needed to do so and financially, it appeared to be a good time to make it happen. Since I had experience in the field, I chose to remain in the church furniture market but focus more on traditional styles. I’d always admired the old, high altars in European churches and hoped to build some myself. Large scale work does require more than one person, and fortunately, I was able to recruit Austin Glidewell to help establish Altare Design, LLC. By this time I’d mastered conventional woodworking techniques and possessed a working knowledge of marketing, website-building, photography, 3D modeling and business tax laws.

Wall-mounted or placed on a table or countertop, this handsome display cabinet is the perfect way to share any collection while keeping it clean and protected at the same time. Featuring tempered glass doors and three shelves, the cabinet’s design calls for all straight cuts and straightforward construction techniques (simple cut-outs give the effect of
The video explains the step by step process of making a nice wooden phone stand from scratch. My first wooden holder was not the best one, but it was good enough to motivate me to make more. I now possess 10 mobile wooden stands in different shapes and styles. And if I can make this, you too can make one yourself. Search the internet for more mobile holder ideas and start making one now. 

Sound overwhelming? Then just start off focusing on Disston saws. The Disston saws were manufactured by the millions and are the easiest to find, and most are of exceptional quality, especially the below common models. Remember to buy pre 1940’s era vintage hand saws. Here are some ebay searches for wood saws. To ensure that you don’t over-pay, when you’re on ebay click “sold” to see what they’re selling before and to see which saws are desirable. It’s fun research:
Stranded: Here is a link; http://www.leevalley.com/US/shopping/Instructions.aspx?p=41059 to some info for the various Japanese saws where they briefly discuss using two hands and also mention Westerners having a problem with that technique? Just to take the topic a little further: If you are doing small dovetails or small tenons, you might get away with one hand because the depth of cut is usually shallow. And if you are using a Japanese dovetail saw with back stiffener that will help with tracking. Personally I like to start my cut with one hand (1/16-1/8" depth), usually on the corner closest to me then switch to two hands always with a gentle grip to let the saw do the cutting, sometimes with a dusting of pounce on my hands for a better grip, but not tight. I have been using this technique for many years and still find little subtleties (mindfulness) that provide improvement. Practice, Practice, Practice--Enjoy, Mainewood
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.
×