To start off this list of simple woodworking projects is a DIY sawhorse which will be very helpful to you if you don’t own a ShopBot Buddy. A sawhorse always comes in handy especially if you have more plans of woodworking in the future. Before you get started on this woodworking project, get one of these extension cords with built-in outlets for your power tools to help you out!
Cut off a 21-in.-long board for the shelves, rip it in the middle to make two shelves, and cut 45-degree bevels on the two long front edges with a router or table saw. Bevel the ends of the other board, cut dadoes, which are grooves cut into the wood with a router or a table saw with a dado blade, cross- wise (cut a dado on scrap and test-fit the shelves first!) and cut it into four narrower boards, two at 1-3/8 in. wide and two at 4 in.
Aside from modern heirloom saws (like Lie-Nielsen & other high-end custom saw makers) I would stay away from any cheap hand saws manufactured after World War II. Yes, this is the same advice that I gave with hand planes. Tool quality really declined after WWII. What brands should you look for? Historically there were a lot of hand saw makers, because saws are easier to manufacture than hand planes. Here are some of the old and new quality saw makers (in alphabetical order). The blue links lead to eBay and other searches for those hand saw brands so you can compare different models (some of the antique brands are not always available on eBay, so keep checking back):
If you’ve ever found yourself at the lumberyard with several boards that are too long for the bed of your truck, you’ll appreciate having a panel saw. Carrying around a circular saw and hoping to find an outlet is more hassle than it’s worth. But leaving a panel saw (8 to 12 tpi) in the truck is no problem. Lay the boards in the bed with the gate down, and cut them to fit. I even use a panel saw in the shop to cut a board to rough length when it’s too big for my chopsaw.
Handsaws are great for getting into tight spaces, too. a coping saw is the perfect tool to cut out the waste between dovetails. The thin blade can fit into even the tightest pin socket and make a turn along the baseline, removing the waste in seconds. Chopping out waste with a chisel takes much longer, and routing it out is possible only when there’s enough clearance between the tails to fit the bit.
Apprenticeships or internships are definitely a viable path. They can be the fastest way to learn due to all the hands-on experience, and some will even provide a small income. Those opportunities can be hard to find for those not already familiar with the woodworking scene. Supporting skills such as accounting, business, marketing, photography and website administration can be learned formally via conventional education such as college, but it’s tough to dedicate time and money in that route while also trying to master woodworking. Books and the internet are handy in this regard, and I did learn to setup WordPress websites by utilizing a basic Lynda.com subscription.
Here’s a traditional Swedish farm accessory for gunk-laden soles. The dimensions are not critical, but be sure the edges of the slats are fairly sharp?they’re what makes the boot scraper work. Cut slats to length, then cut triangular openings on the side of a pair of 2x2s. A radial arm saw works well for this, but a table saw or band saw will also make the cut. Trim the 2x2s to length, predrill, and use galvanized screws to attach the slats from underneath. If you prefer a boot cleaner that has brushes, check out this clever project.
Today I am going to show you how we build our very own a pallet end Table! As I have been obsessed with some natural wood textures and was also lusting after a pallet table which was very similar to this one. I always prefer everyone to make things yourself rather than buying them, because what is the meaning of spending some money when you are able to build exactly the look you saw in home décor or somewhere else at a fraction of the cost. I promise that it is a simple plan to do and you can make it in a day or half.
Fir, also known as Douglas Fir, is very inexpensive and common at local home centers. It has a characteristic straight, pronounced grain with a red-brown tint. However, its grain pattern is relatively plain and it does not stain well, so Fir is commonly used when the finished product will be painted. While commonly used for building, this softwood would also be suitable for furniture-making as well.
Slice, dice and serve in style on this easy, attractive board. We’ll show you a simple way to dry-fit the parts, scribe the arc and then glue the whole thing together. We used a 4-ft. steel ruler to scribe the arcs, but a yardstick or any thin board would also work. Find complete how-to instructions on this woodworking crafts project here. Also, be sure to use water-resistant wood glue and keep your board out of the dishwasher or it might fall apart. And one more thing: Keep the boards as even as possible during glue-up to minimize sanding later. For great tips on gluing wood, check out this collection.
Cut the 6-1/2-in. x 3-in. lid from the leftover board, and slice the remaining piece into 1/4-in.-thick pieces for the sides and end of the box. Glue them around the plywood floor. Cut a rabbet on three sides of the lid so it fits snugly on the box and drill a 5/8-in. hole for a finger pull. Then just add a finish and you’ve got a beautiful, useful gift. If you don’t have time to make a gift this year, consider offering to do something for the person. You could offer to sharpen their knives! Here’s how.