Stranded: Here is a link; http://www.leevalley.com/US/shopping/Instructions.aspx?p=41059 to some info for the various Japanese saws where they briefly discuss using two hands and also mention Westerners having a problem with that technique? Just to take the topic a little further: If you are doing small dovetails or small tenons, you might get away with one hand because the depth of cut is usually shallow. And if you are using a Japanese dovetail saw with back stiffener that will help with tracking. Personally I like to start my cut with one hand (1/16-1/8" depth), usually on the corner closest to me then switch to two hands always with a gentle grip to let the saw do the cutting, sometimes with a dusting of pounce on my hands for a better grip, but not tight. I have been using this technique for many years and still find little subtleties (mindfulness) that provide improvement. Practice, Practice, Practice--Enjoy, Mainewood
I studied forestry at Penn State University and then spent ten years working in the utility line clearance industry with the Asplundh Tree Expert Co. While building my house, I began to get into carpentry and woodworking, and later went to work as a finish carpenter. Eventually, I started taking on some minor woodworking jobs. I realized I needed some real shop experience, so I took a job in a stair shop building custom staircases for about five years. While there, I began to set up a shop of my own with the intention of going into business for myself, which I did in 1998. I’ve been on my own since.My typical day is usually pretty simple. I’ll spend an hour in the morning on the computer promoting my shop and looking for leads. Around 8:00 A.M. I open up the shop and work on whatever I’m doing until 4:00 or 5:00 P.M.
With two varieties, red and white, oak is known to be easy to work with and relatively strong. However, furniture makers often opt for white oak over red oak for its attractive figure and moisture-resistance.[12] Depending on the kind needed, oak can probably be found at a local home center or a lumberyard for a bit pricier than other hardwoods.[12][13]
Working on one side at a time, glue and nail the side to the back. Apply glue and drive three 1-5/8-in. nails into each shelf, attach the other side and nail those shelves into place to secure them. Clamps are helpful to hold the unit together while you’re driving nails. Center the top piece, leaving a 2-in. overhang on both sides, and glue and nail it into place. Paint or stain the unit and then drill pilot holes into the top face of each side of the unit and screw in the hooks to hold your ironing board. Mount the shelf on drywall using screw-in wall anchors.
If you have more complex woodworking or carpentry jobs, choose a hand saw that is tailor made for these tasks like the Vaughan BS240P Pull Stroke Rip Handsaw or the Crown FLINN1 10-Inch Dovetail Saw. Also, the type of hand saw will depend on whether you be cutting with the grain or across the grain. There are 3 main types of basic hand saws: a cross cutting saw, a rip saw, and a dovetail back saw.
Although the term "woodworker" may evoke the image of a craftsman who uses hand tools to build ornate furniture, the modern woodworking trade is highly technical and relies on advanced equipment and highly skilled operators. Workers use automated machinery, such as computerized numerical control (CNC) machines, to do much of the work with great accuracy.
HomemadeHomeIdeas is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com. Pages on this site may include affiliate links to Amazon and its affiliate sites on which the owner of this website will make a referral commission.
Woodworkers are employed in every part of the secondary wood products industry, from sawmill to finished product, and their activities vary. They set up, operate, and tend all types of woodworking machines, such as drill presses, lathes, shapers, routers, sanders, planers, and wood-nailing machines. Operators set up the equipment, cut and shape wooden parts, and verify dimensions, using a template, caliper, and rule.

They both are both nice, but neither cut quite as well as the “progressive pitch” Lie-Nielsen dovetail saw that I’d tried at one of my traditional woodworking classes. The Lie-Nielsen dovetail back saw had the perfect thickness and such a comfortable pistol grip. I finally realized that I had spent more money on two dovetail saws that didn’t quite satisfy me than I had on a perfect new Lie-Nielsen dovetail saw ($125). So I ordered this dovetail saw from Lie-Nielsen, and have loved it for many years (even after buying many more dovetail saws)!
I believe there are demos on the use of the Dozuki on a number of sites, but you would, do best watching some from Japan. Also, I think the sites of Japanese Woodworkers Tools and Lee Valley Tools might have some information or you could search "using dozuki saws" or using Japanese saws". If I can locate a good site I'll post it here--Good luck, Mainewood
As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.
As you can see in the image, this shelf goes on both sides of the corner wall. It looks beautiful and can be used to organize books, trophies, pictures frames and many other things. The strength and design of the shelf depends on how properly you build it. First time workers definitely need some guidance to help them with the process. Therefore, I am including this basic video that I found on YouTube that demonstrates the process of making corner wall wooden shelves.
My hands-down favorite thing to do is develop the process for manufacturing a new product. This involves figuring out how to design a product so that it’s not only durable and functional, but also economical to build. Then all the jigs, fixtures and CNC programs have to be created and tested until the whole process is running smoothly. Up to now, the most challenging project has been our line of wooden sunglasses which were developed for a specific client. We spent hundreds of hours just figuring out how to build the first pair then hundreds more hours refining the process until they became profitable.
Because the Dozuki has such a finely produced blade (if it is a quality saw) then the smallest of deflection while using one hand allows it to track away from your intended cut. Note: If you hold one hand out in front of you with no saw in it, and your hand folded as if you were holding the saw, then pull your hand back as if you were cutting (without trying to keep it straight), you will notice that your hand will twist usually to the inside, but not always--there lies the problem--since you need only one stroke to throw the tracking off.
×