The space behind a door is a storage spot that’s often overlooked. Build a set of shallow shelves and mount it to the wall behind your laundry room door. The materials are inexpensive. Measure the distance between the door hinge and the wall and subtract an inch. This is the maximum depth of the shelves. We used 1x4s for the sides, top and shelves. Screw the sides to the top. Then screw three 1×2 hanging strips to the sides: one top and bottom and one centered. Nail metal shelf standards to the sides. Complete the shelves by nailing a 1×2 trim piece to the sides and top. The 1×2 dresses up the shelf unit and keeps the shelves from falling off the shelf clips.


A dozuki saw has a thin, flexible blade, with fine teeth and a straight handle, which makes it well-suited to flush-cutting pegs. The flexible tip helps it get close to the base of a pin, and the straight handle is easier to hold and control with the saw on its side than a pistol grip would be. Get a crosscut dozuki with about 20 tpi. So why not just use a flush-cut saw? Their teeth have no set, so they clog and don’t cut as well. Dozukis don’t have those problems. The thin blade can kink, so get a saw with a replaceable blade.
The amazing 15-inch hand saw has special ‘triple ground’ extra sharp teeth that can cut and rip through wood three times faster than other similar hand saws. The universal tooth grind is designed to remove material quickly, and its innovative design combines the speed of a coarse-cutting saw with the finish of a fine-cutting saw, so you can expect a clean and accurate cutting action. 

A good Japanese pull saw isn't cheap, perhaps $60-75, and they have to be replaced when dull. They also tend to be brittle and teeth can break off if you nick them on your vice. Also, after trying to improve my technique for 9 years, I still can't follow a straight line, the saw goes where it wants to. My newest Japanese saw came with instructions that said to grip the handle with two hands, which I had never thought about nor read anywhere. Could you comment on that, Matt? Thanks.
The items you’ll need for this project include wood board, power drill, tape measure, adhesive, etc. Read the tutorial for details. Follow the steps properly to make a nice and strong wall rack. This rack makes use of magnets to hold metal items. The tutorial explains the procedure for building this beautiful wall rack. Make sure to use only high quality items for any woodworking project. Use the rack only to hang items that are not too heavy for the magnet to hold. Also, be careful while working around this wall rack and beware of the knives falling off the rack.

I’ve got a three other bits of advice: First of all, get really, really good at woodworking. There are lots of people who enjoy it as a hobby. To sell your services, you’ve got to be able to do far superior work or do it much faster than everyone else (preferably both). Failure to do so means competing against hundreds of amateurs who make things for the pleasure of it, then sell their work at cost to fund the hobby. Second, develop great people skills. Most professionals do custom work and few focus on selling a product. Most of them sell a service, and a big part of that is getting customers to enjoy the experience of collaborating with a woodworker to create their dream products. If your customers don’t like you, they can usually save time and money by getting something from an online catalog. People who buy handcrafted items from woodworkers are often attracted to the idea of supporting artisans. The face behind the work is important to them. Last, develop an iron-clad work ethic. In this field you’re directly trading time for money, and that time is very limited. It’s important to be productive, so try to get 40 hours of actual productivity (as in making things) every week. Accounting, phone conversations and social media marketing may be important, but none of them provide an actual paycheck, so they don’t count as productive work.


This super easy recycled pallet Christmas tree created by using some pallets is one of my favorite DIY projects. It might have all the components of your craft, a little bit new but rustic Christmas tree. It is perfect for both outdoor and indoor décor pieces! We are including the source tutorial for this DIY project below. Source tutorial includes step by step details of this process with diagrams and images.
Working with reclaimed wood is a savvy use of resources, and the material's country appeal is undeniable. With just a saw and a small drill, you can reuse old fencing to make these simple woodworking projects: picket-inspired picture frames. Finish them off by hot-gluing clothespins or bulldog clips to hang your prints. Here’s a step-by-step guide. 

Although the term "woodworker" may evoke the image of a craftsman who uses hand tools to build ornate furniture, the modern woodworking trade is highly technical and relies on advanced equipment and highly skilled operators. Workers use automated machinery, such as computerized numerical control (CNC) machines, to do much of the work with great accuracy.
Woodworkers use geometry, arithmetic, algebra, calculus, and statistics to measure materials and during the planning stages of projects.  On any given job, they will calculate sizes, dimensions, distances, and quantities of materials.  Computer skills and knowledge of relevant software also benefits woodworkers with job-estimating, project management, and basic spreadsheet or word processing.  Woodworkers should be detail-oriented, have good people skills, have steady hands, and physical strength, especially when lifting 100-pound sheets of plywood.
And finally, we ended up with an original, elegant, functional and an inexpensive bar that we were able to make ourselves. Even though this shelf project was created as a simple way of adding some useful decorative pieces. Check out our this DIY beautiful piece which is made of reclaimed pallets. It doesn’t involve any scrap, but it is still the project that will look elegant in your room.
For your kitchen, it can work as a knife rack. It gives you easy access to all essential tools while saving space. In addition, it adds a nice visual appeal to your kitchen wall. You can customize your wall rack with different materials, designs and styles. I am here sharing the source link to the step by step tutorial about how to make a rustic wall knife rack.
There are many other great tutorials you can find on the internet, but they all need many tools to build. You might not have a table saw, a router, or miter saw and of course, it costs hundreds of dollars. And you can sell this Deck cooler at almost no cost and make a handsome profit. By having a drill and impact driver plus any type of saw, you can build it easily.
Do you want to use an oil stain, a gel stain, a water-based stain or a lacquer stain? What about color? Our ebook tells you what you really need to know about the chemistry behind each wood stain, and what to expect when you brush, wipe or spray it on. It’s a lot simpler than you think! This is the comprehensive guide to all the varieties of stain you will find at the store and how to use them. 

Someone interested in woodworking now needs to get computer training to be able to lay out jobs on a CAD program. CNC machines are also used in shops where they lay out the cabinetry for you and cut the parts. Working with these machines takes skill in knowing how to build the cabinet and knowing how to use the computer programs. Also, math is used all day, every day in woodworking, and the better you are at math the better you can build things.
"Mike was referred to me by a family member. I enjoyed his attitude and attentiveness to what my ideas were for my basement. He did the framing in the basement and built two bedrooms and added the bathroom. He was a huge help in designing the area because I needed the bedrooms to be built where the egress windows are. He was always professional and responsive. I highly recommend Mike to anyone needing a carpenter for anything."
Stranded: Here is a link; http://www.leevalley.com/US/shopping/Instructions.aspx?p=41059 to some info for the various Japanese saws where they briefly discuss using two hands and also mention Westerners having a problem with that technique? Just to take the topic a little further: If you are doing small dovetails or small tenons, you might get away with one hand because the depth of cut is usually shallow. And if you are using a Japanese dovetail saw with back stiffener that will help with tracking. Personally I like to start my cut with one hand (1/16-1/8" depth), usually on the corner closest to me then switch to two hands always with a gentle grip to let the saw do the cutting, sometimes with a dusting of pounce on my hands for a better grip, but not tight. I have been using this technique for many years and still find little subtleties (mindfulness) that provide improvement. Practice, Practice, Practice--Enjoy, Mainewood
The GreatNeck Hand Saw is proudly made in the USA and it is an excellent choice for all-purpose woodworking applications. With a strong high carbon 26-inch steel blade and 10 teeth-per-inch (TPI), the GreatNeck is a highly versatile tool that you can use for rougher, more aggressive cuts as well fine, detailed cuts and it will cut effortlessly through all types of wood from soft wood to hardwood lumber such as red oak and maple, so all of your projects will be done quickly and efficiently.
Hi there, I'm glad that you are here. Firstly, let me introduce you that my name is Kevin Smith and I'm a coffee addicted guy, a blogger. Secondly, the reason why I create this website is to analyze what's the best products on the market with high quality and affordable price so that I make a decision to buy the right products for my family, friends and me. Thirdly, I just want to learn more about Home & Improvement Tools and Appliances so that I could improve my sweet little home.
Gripping the hand saw is effortless and easy to control even when you are working with hard wood as the thick plastic handle has an ergonomically designed rubber grip which is comfortable to hold and helps to reduce any slipping. A versatile hand saw, it can be used for DIY renovations or carpentry jobs as the back of the saw can be used to mark 45 and 90-degree angles for quick and easy measuring.
Another important factor to be considered is the durability of the wood, especially in regards to moisture. If the finished project will be exposed to moisture (e.g. outdoor projects) or high humidity or condensation (e.g. in kitchens or bathrooms), then the wood needs to be especially durable in order to prevent rot. Because of their oily qualities, many tropical hardwoods such as teak and mahogany are popular for such applications.[9]
It has a narrow and tapered blade, usually pointed at the end. A compass saw typically has about 8-10 teeth per inch, which can go up to 20 teeth per inch if you are cutting harder materials. A compass saw comes with a pistol grip, which is best suited if you are working in confined places. The pointed end helps you penetrate soft materials without requiring a pilot hole. 

Hand saw blades are usually sharpened to two different tooth configurations, “Rip” and “Cross Cut”. You can change any saw’s tooth shape with saw sharpening tools.  There is also a hybrid hand saw tooth configuration that is in between a Rip and Cross-cut shape, called a “Sash” tooth configuration, which is useful if you can only afford one hand saw…but it’s not as proficient at either ripping or cross-cutting). Here are some tooth shape diagrams:
Have you got an old whiskey barrel at home that you haven’t used for ages? If yes, this project is for you. You can make a really beautiful coffee table from that old whiskey barrel in a few easy steps. Apart from a coffee table, whiskey barrels can also be used to build several other furniture items. But that is a talk for later. Here, we will discuss how to make a coffee table from a whiskey barrel.
Woodworkers set up, operate, and tend all types of woodworking machines, such as saws, milling machines, drill presses, lathes, shapers, routers, sanders, planers, and wood-fastening machines. Operators set up the equipment, cut and shape wooden parts, and verify dimensions, using a template, caliper, and rule. After the parts are machined, woodworkers add fasteners and adhesives and connect the parts to form an assembled unit. They also install hardware, such as pulls and drawer slides, and fit specialty products for glass, metal trims, electrical components, and stone. Finally, workers sand, stain, and, if necessary, coat the wood product with a sealer or topcoats, such as a lacquer or varnish.
Re-sawing is the method for making two thinner pieces out of one board. Say you need two pieces of wood 3/8” thick, but only have a 1” thick board, you can slice the wood into to thinner pieces by cutting down the middle, making the two pieces. This is not the same as ripping, as you’re not cutting down the width of the board, but through the thickness instead.
Although the term “woodworker” may evoke the image of a craftsman who uses hand tools to build ornate furniture, the modern woodworking trade is highly technical and relies on advanced equipment and highly skilled operators. Workers use automated machinery, such as computerized numerical control (CNC) machines, to do much of the work with great accuracy.
Everyone wants to add some decorative stuff to their furniture in the home or patio. These elegant pumpkin décor pieces can be a nice add to their décor, You can build these pieces in less than a day or more than it in case if you are not that skilled. You don’t need to be a professional woodworker to build this one, rather, if you have control on some of the basics of woodworking than it’s not a difficult task to build for you.
Upon graduating from high school, I wasn’t sure exactly what career to pursue, but I knew it had to be something that involved creating things with my hands. I’d always had natural talent working with tools, and despite having been an A-average student, I was never fond of conventional academics. Not having better plans at the time, I took one calculus course, got an “A”, then promptly decided two things: I didn’t enjoy college and taking on any debt would force me into a dull, conventional 9-5 job until the debt could be paid off. I didn’t know this back then, but I was pretty much a textbook case of the restless student with the entrepreneurial spirit. Just a few months later, I got the opportunity to accept an apprenticeship at Remmert Studios which was an incredible break. It was a result of reading a local newspaper article about the business, then going to meet the owner. Not many are able to break into woodworking that easily, especially in the high-end market. That company did a lot of contemporary furniture for churches, and being short-staffed, it wasn’t long before I was given a full-time position.While working that job, I was also taking week-long classes at Marc Adams School of Woodworking as time and money permitted. The combination of hands-on work and classroom study allowed me to acquire new skills very quickly. Being at the school also netted an internship opportunity with one of North America’s most prestigious furniture-makers, Michael Fortune. 

Any serious woodworker knows that square and flat Any serious woodworker knows that square and flat stock is the key to producing fine work so it’s time to skip the hand tools and graduate to the JJ-6HHDX 6 in. long bed jointer. This beast boasts a helical insert cutter head with staggered carbide inserts yet runs quietly and ...  More + Product Details Close
This can be an elegant centerpiece of your patio furniture or room furniture. Building this project does not need any professional skills, but anyone with basic woodworking knowledge and skills can build this project easily. This project will take three or four hours of your time to build, or can be a day if you take some breaks during the work as I did.
The miter saw is a multi function electric saw. You can use a miter saw to make cross cuts (perpendicular to the grain of the wood), miter cuts (an angled cut across the width of the wood), bevel cuts (a type of angled cut where you cut across the thickness of the board) and compound cuts (a mix of the bevel and miter cut). To make each of these cuts, you have to adjust the miter saw accordingly.
Just make sure to use non-toxic wood and non-toxic finishes like Raw Linseed Oil or Carnauba Wax so that dangerous chemicals from other woods and finishes doesn’t contaminate the food that goes onto the cutting board. You can also opt to include an indent for the knife, so the chef can put the knife into the cutting board when the knife is not currently in use.
Perfectly customizable for any home bar or kitchen, wooden coasters are incredibly easy to make and perfect for the beginner craftsman or craftswoman. All it really takes is some precise (or imprecise, depending on the style you wish to achieve) cuts, a little to a lot of sanding, a tiny bit of finish, and the optional design you want on the coaster.
This box is the fifth generation of this design. After each production run of about 20 boxes, I make slight design changes to enhance the look and simplify the machining. Any hardwoods would work, but since the box uses so little lumber, I prefer to incorporate highly figured woods. For safety, ease of construction and consistent cuts, I use a jig for bevel-cutting the legs and another jig for beveling the top surface of the lid.
Silky offers the ultimate professional woodworking and carpentry saws for both the professional and hobbyist. Laser-cut, impulse hardened blades for exceptional performance and incredibly long service life are the hallmark of all Silky woodworking saws. All Silky woodworking saws use unique alloy steel engineered and produced exclusively for Silky Saws.
This box is the fifth generation of this design. After each production run of about 20 boxes, I make slight design changes to enhance the look and simplify the machining. Any hardwoods would work, but since the box uses so little lumber, I prefer to incorporate highly figured woods. For safety, ease of construction and consistent cuts, I use a jig for bevel-cutting the legs and another jig for beveling the top surface of the lid.
Shorter hand saws (around 20-inches long) are officially called “panel saws” because they can fit in the panel of a large tool chest, and they are more suited for fine furniture making. Most normal hand saws run from 24-inches to 30-inches long. Many people mistakenly call all saws of this type “panel saws”. But don’t be rude and correct them! Try out different sizes to see what length you’re comfortable with. 

With the right tools and materials, what you build is only limited by your imagination and creativity. So why not have a little fun with the kids and teach them something at the same time? Our woodworker tools and woodworking supplies will help you put together an easy birdhouse, squirrel feeder or butterfly house. The kids will love to use our paint samples to add their creative touch, and will enjoy displaying the finished product in the backyard.
In being self-employed, one day will greatly vary from the next, but generally, I start in the morning by dealing with in-town errands or head right to the shop if there are none. Once at the shop, there’s an e-mail check, then a brief glance at various websites to look for new developments related to our market and clientele. Then the real workday starts. I’ve got a bunch of notes regarding current projects taped next to my computer and will make a list for the day’s tasks by picking the highest priority items from the notes. The goal is to get that stuff accomplished by the end of the day. There are two of us in the shop, but we usually work on separate projects, so that’s why I have my own to-do list. Some days are spent on the computer designing or creating programs for the laser or CNC. Other times we’re doing runs of sunglasses or guitar parts which we sell wholesale to other businesses. In which case, I may be operating the laser or CNC. Despite the high-tech tooling, there’s still a lot of bench work to do, and that can involve cutting and fitting joints with chisels and hand planes. Besides that, there’s always plenty of rough lumber to mill since no project can begin until boards are flattened, surfaced and cut to dimension.
All content on this blog is the property of Just the Woods, LLC. You are welcome to share my content (to include one photo only) as long as you provide a link back the original post. DO NOT copy entire posts, or crop, edit, or remove watermarks from photos without written permission from me first. Sharing a post from Just the Woods in a capacity where YOU will be compensated is not permitted. Thank you!
×